Priming Sugar Calculator

Calculate how much priming sugar to add at bottling so bottle-conditioned beer carbonates to your target level — accounting for the CO₂ already dissolved in the beer.

Volume that goes into bottles

Warmest temperature after fermentation

1.0–4.5 vol

How to use this calculator

  1. Confirm fermentation is finished: the same gravity reading on two or three consecutive days.
  2. Enter the volume that will actually go into bottles, after losses to trub and sediment.
  3. Enter the warmest temperature the beer reached after fermentation ended — not today's temperature.
  4. Enter your target carbonation in volumes of CO₂ for the style (see below).
  5. Choose your sugar, weigh out the result, dissolve it in a little boiled water, let it cool, and stir it gently and evenly into the bottling bucket before filling.

What the inputs mean

Volumes of CO₂ measure carbonation: one volume is one litre of CO₂ dissolved in each litre of beer. Typical targets are 1.8–2.2 for British ales, about 2.2 for porters and stouts, 2.4–2.6 for American ales, 2.5–2.8 for lagers, 2.8–3.5 for wheat beers and 3.0–4.0 for strong Belgian ales.

Residual CO₂ is the gas left over from fermentation. Cold beer holds more of it, warm beer less — and the level is fixed by the warmest temperature after fermentation, because gas that escaped does not come back. The priming sugar only has to supply the difference.

Sugar type matters because a gram of each sugar yields a different amount of CO₂. Dextrose (corn sugar) is the reference; table sugar actually yields slightly more CO₂ per gram, while honey and dry malt extract contain water and unfermentable material, so more weight is needed.

Formulas

Residual CO₂ already in the beer (AHA / Brewer's Friend fit, T in °F):

Residual CO₂ = 3.0378 − 0.050062 × T + 0.00026555 × T²

Sugar needed for the remaining gap:

Sugar (g) = (target − residual) × litres × 4.0 ÷ yield

The 4.0 constant is grams of dextrose per litre per volume of CO₂. The yield is each sugar's CO₂ output per gram relative to dextrose: dextrose 1.00, table sugar 1.05, dry malt extract 0.68, honey 0.75.

Example

A pale ale of 19 litres reached 20 °C (68 °F) after fermentation and is bottled for 2.5 volumes. It already holds 0.86 volumes, leaving a gap of 1.64 volumes, so it needs 1.64 × 19 × 4.0 = about 125 g of dextrose (4.4 oz).

Accuracy & limitations

  • The residual-CO₂ formula is an empirical fit for beer fermented at atmospheric pressure. Beer fermented under pressure (spunding) holds more CO₂ than the formula predicts.
  • The fermentability of honey and DME varies by product and batch, so their results are less exact than dextrose or table sugar.
  • The result assumes the sugar is fully dissolved and evenly mixed. Uneven mixing is the usual cause of some bottles gushing while others stay flat.
  • Accepted ranges: 1–200 L, warmest temperature 0–30 °C, target 1.0–4.5 volumes. If the target is at or below the CO₂ already in the beer, no sugar is needed and no result is shown.

FAQ

Do I need a secondary fermenter for bottle conditioning?

No. Bottle conditioning is itself a secondary fermentation — it happens in the bottle, driven by the yeast still in suspension. Racking to a separate secondary vessel first is optional and mostly adds oxidation and infection risk. What actually matters is that primary fermentation is completely finished before you bottle: take gravity readings two or three days apart and only prime when they are identical.

How do honey and DME compare with dextrose?

Both carry less fermentable sugar per gram, so you need more of them. Honey is roughly 80 % fermentable sugars and about 17 % water, so it takes about a third more by weight than dextrose. Dry malt extract is only about two-thirds fermentable — the rest is unfermentable dextrins and protein — so it takes roughly half again as much. The calculator applies these factors for you. Both also add flavour: honey a faint floral note (mostly fermented away at priming doses), DME a little extra malt and body, and DME carbonates a bit more slowly.

Which temperature should I enter — the bottling temperature or the fermentation temperature?

Neither, exactly: enter the warmest temperature the beer reached after fermentation finished. Residual CO₂ is set by that warmest point, because CO₂ escapes as beer warms and does not dissolve back when the beer is cooled again. If you enter a cold-crash or fridge temperature, the calculator overestimates the CO₂ still in the beer, you add too little sugar, and the bottles come out under-carbonated.

Can priming sugar make bottles explode?

Bottle bombs come from more fermentable sugar than the bottle can hold: priming a beer that has not finished fermenting (its remaining wort sugar adds to the priming sugar), a large weighing error, unevenly mixed sugar, or a high target in thin glass. Ordinary beer bottles are generally safe to about 3 volumes of CO₂; for wheat-beer or Belgian targets above that, use heavy Belgian or champagne bottles. Weigh the sugar on a scale rather than measuring by volume, dissolve it in a little boiled water, and mix it evenly through the batch.