How to use this calculator
- Enter the post-boil wort volume you collected (gal or L) and the original gravity you measured in the fermenter.
- For each malt, enter its weight and its extract potential in PPG from the maltster's specification. There are four slots; leave the ones you do not need empty.
- Gravity and volume must describe the same wort in the same state: correct the gravity reading for temperature, and measure the volume of that same wort — ideally both in the fermenter.
- The result appears instantly: brewhouse efficiency, the potential and actual gravity points behind it, and the gravity this grain bill would have given at 75% efficiency. Use a dot or a comma as the decimal separator; changing a unit converts the values you have already entered.
What the inputs mean
Wort volume is the volume collected after the boil — what actually made it into the fermenter. Not the pre-boil volume and not the recipe's nominal batch size: every litre lost to kettle dead space, trub and hoses is a litre whose sugar does not count, and brewhouse efficiency is meant to capture exactly that.
Original gravity is the gravity of that same wort, temperature-corrected. A hydrometer reading taken at 60 °C reads several points low; either cool the sample or use thehydrometer temperature correction first. A refractometer reading needs its own correction once alcohol is present, but for pre-fermentation OG it only needs its Brix-to-SG conversion.
Malt potential (PPG) is the extract potential printed on the malt specification, in points per pound per gallon: a malt rated 37 PPG would yield a gravity of 1.037 if one pound were mashed into one gallon with perfect extraction. Typical values: pale and pilsner malts 36–38, wheat malt 38–39, Munich 35–36, crystal malts 33–34, roasted malts around 25–30. European specs often state extract as a percentage instead (80% ≈ 37 PPG). If a recipe uses more than four malts, combine the smallest additions into one slot with a weighted-average potential; the points add up linearly, so grouping barely changes the result.
Formula
The gravity-points method compares the extract the grain bill could possibly give with the extract that actually arrived in the fermenter:
potential points = Σ (malt weight in lb × PPG)actual points = (OG − 1) × 1000 × wort volume in galefficiency % = actual points ÷ potential points × 100The predicted gravity at 75% simply runs the same arithmetic forwards: OG = 1 + (potential points × 0.75 ÷ volume in gal) ÷ 1000. That is the number to scale a recipe with if your system runs at the common 75% benchmark — or compare it with your measured efficiency to see how far your system sits from it.
Example
A single-malt pale ale: 10 lb of pale malt at 37 PPG, collected5 gallons of wort at OG 1.050. Potential points = 10 × 37 =370; actual points = 0.050 × 1000 × 5 = 250. Efficiency = 250 ÷ 370 ≈67.6%. At 75% the same grain bill would have given 1 + (370 × 0.75 ÷ 5) ÷ 1000 ≈1.056. In metric units — 4.54 kg in 18.9 L — the result is identical.
Accuracy & limitations
- This measures brewhouse efficiency — gravity in the fermenter against the grain's total potential. It is not mash or conversion efficiency: losses in the kettle, trub and dead space all lower this number, by design.
- An efficiency over 100% cannot be real. It means the volume or gravity was mis-measured (or a potential was typed too low) — treat it as a diagnostic, not a result.
- Malt potentials are specification values and vary by maltster and lot; the fine-grind laboratory extract behind a PPG rating is never fully reachable in a real mash, which is why even excellent systems stay below about 90%.
- Measure volume and gravity on the same wort in the same state. Hot wort expands by roughly 4% and reads low on a hydrometer, so a volume paced off at 100 °C against a gravity corrected to 20 °C quietly invents or destroys several efficiency points.
- Accepted ranges: wort volume 1–1000 L, each malt 0–100 kg, potential 20–46 PPG, gravity 1.000–1.200. At least one malt with some weight is required. Planning a brew day? Start with thestrike water calculator for mash temperatures, and check thebeer colour calculator for what the same grain bill will look like.
FAQ
What is the difference between brewhouse and mash efficiency?
Mash efficiency stops at the kettle: it compares the extract in the wort you collected with the grain's potential, and splits further into conversion efficiency (how completely the mash turned starch into sugar) and lauter efficiency (how much of that sugar you rinsed into the kettle). Brewhouse efficiency — what this calculator measures — follows the wort all the way into the fermenter, so it also counts kettle dead space, trub and transfer losses. It is always the lower number, and it is the one that matters for recipes, because recipe OG is stated for the fermenter.
My efficiency came out over 100% — what went wrong?
An efficiency above 100% is physically impossible: you cannot extract more sugar than the grain contains. It always means a measurement error — most often the volume (a fermenter marked 20 L that actually holds 21), a gravity reading taken on hot wort without temperature correction, a hydrometer that reads high in plain water, or a malt potential typed in too low. Check those four before believing the number; the calculator reports it as-is precisely so the red flag is visible.
What brewhouse efficiency should I expect?
Most homebrew systems land between 65% and 75%. Batch sparging typically gives 65–72%, fly sparging and a fine crush push towards 75–80%, and brew-in-a-bag with no sparge often sits at 60–70%. Commercial breweries run 80–95%. Consistency matters more than the level: a system that reliably hits 68% produces better beer than one that swings between 60% and 80%, because every recipe can be scaled to the number you actually get.
Why does efficiency drop on big, high-gravity beers?
Two reasons. First, a thicker mash (less water per kilo of grain) converts and rinses less completely. Second, with a fixed sparge volume there is proportionally less rinse water per kilo of grain, so more sugar stays behind in the spent grain. Expect a barleywine or imperial stout to come in 5–10 points below your standard pale ale on the same system — which is why many brewers plan big beers at a lower efficiency, or make up the difference with a longer boil or a little extract.