How to use this calculator
- Enter the pre-boil volume — the wort in the kettle when the boil starts.
- Enter the boil time in minutes.
- Fill in either the volume after the boil (if you measured it) or your evaporation rate (if you know it). The calculator derives whichever one you leave blank.
- Optionally add the pre-boil gravity to see the post-boil gravity.
- Plan the brew around the result: it is the volume and gravity you will chill and pitch into, before cooling shrinkage and trub losses.
What the inputs mean
Pre-boil volume is everything collected in the kettle — if you are still working out how much wort to collect, the strike water calculator covers the mash end of the day, and the mash efficiency calculator covers whether that wort carries the extract you expected. Boil time is the full duration at a rolling boil. Volume after the boiland evaporation rate are two views of the same loss: the rate is quoted as a percentage of the pre-boil volume per hour, so a 10 %/hr rate on 28 L means 2.8 L gone in a one-hour boil. Pre-boil gravity is optional and only affects the gravity result.
Formula
Evaporation is linear in this model — the rate is a percentage of the pre-boil volume per hour:
Loss = pre-boil volume × rate (%/hr) × hoursExtract does not evaporate, so gravity points (SG − 1, × 1000) are conserved and concentrate in inverse proportion to the volume:
Post-boil points = pre-boil points × pre-boil volume ÷ post-boil volumeExample
A kettle with 28 L before the boil, boiled for 60 minutes at10 %/hr: the loss is 28 × 10 % × 1 = 2.8 L, leaving 25.2 L. A pre-boil gravity of 1.040 (40 points) concentrates to 40 × 28 ÷ 25.2 = 44.4 points, so the post-boil gravity is 1.044. Run it the other way — enter 28 L, 60 minutes and 25.2 L after the boil — and the calculator hands you the 10 %/hr rate to design the next batch with.
Accuracy & limitations
- The rate is a percentage of the pre-boil volume (the standard kettle-loss convention), not of the shrinking volume, so long boils are not compounded. Some software uses the other convention and will differ slightly on multi-hour boils.
- Your real rate depends on kettle geometry (wide kettles evaporate faster), boil vigor, lid position, humidity and altitude. Treat 8–15 %/hr as a starting range, then calibrate with one measured batch.
- Cooling shrinkage (~4 %) is not evaporation and is not included, and neither are trub and hop losses. Measure the cooled volume in the fermenter for packaging numbers.
- Accepted ranges: pre-boil volume 1–1000 L, boil 5–600 minutes, post-boil volume below the pre-boil volume and at least a tenth of it, rate 1–30 %/hr, gravity 1.000–1.200. Out-of-range values are rejected, not extrapolated.
FAQ
What is a typical evaporation rate for homebrew kettles?
Most homebrew systems lose 8–15 % of the pre-boil volume per hour — roughly 4–6 L/hr on larger kettles, or about 1–1.5 gal/hr on a typical 5-gallon setup. Wide, shallow kettles and a vigorous rolling boil sit at the high end; narrow kettles with a gentle simmer at the low end. Measure your own once (pre- and post-boil volume over a timed boil) and reuse that rate.
My cooled wort volume is lower than the post-boil volume — why?
Two separate effects stack up. Evaporation is the loss during the boil itself. On top of that, hot wort shrinks by about 4 % as it cools to pitching temperature, and trub, hop material and kettle dead space take a further share. This calculator covers evaporation only, so expect the cooled, racked volume to be a little lower than the number it gives.
Does boiling off water change the amount of extract in the wort?
No. Only water (and volatile compounds) leave with the steam; the dissolved extract stays behind. That is why gravity points are conserved: halve the volume and the points roughly double. Boiling longer is a legitimate way to raise the gravity of a wort that came out of the mash too weak — at the cost of volume.
Should I top up the kettle to hit my target volume?
You can, but topping up with water dilutes the gravity back down by exactly the same proportion, so you trade volume for strength. If both the volume and the gravity matter, the better fix is upstream: collect more wort at the right gravity (check your numbers with the mash efficiency calculator) rather than correcting at the kettle.