Keg Carbonation Calculator – PSI from Temperature & Volumes

Find the regulator pressure that holds keg beer at your target carbonation level — the same equilibrium pressure for force carbonating and for serving, worked out from the temperature of the beer in the keg.

Temperature of the beer in the keg

British ales 1.5–2.0 · American ales & lagers 2.2–2.7 · wheat beers 2.7–3.3

How to use this calculator

  1. Measure the temperature of the beer in the keg — not the room, not the fridge setting.
  2. Pick a target carbonation level in volumes of CO₂ for the style (see below).
  3. Read off the serving pressure in psi, bar or kPa.
  4. Set the regulator to that pressure. To carbonate from scratch, leave it connected: at serving pressure the beer reaches equilibrium in one to two weeks.
  5. If you are in a hurry, burst carbonate first (see the FAQ), then drop back to this pressure to serve.

What the inputs mean

Volumes of CO₂ measure carbonation: one volume is one litre of CO₂ dissolved in each litre of beer. Typical targets are 1.5–2.0 for British ales, 2.2–2.7 for American ales and lagers, 2.7–3.3 for wheat beers and German styles, and 3.3 or more for highly carbonated styles such as Belgian strong ales and some sours.

Beer temperature matters because cold beer holds CO₂ much more readily than warm beer. The same 2.5 volumes need about 8 psi in a keg at freezing and over 25 psi in a warm keg — which is why a pressure copied from someone else's setup, without their temperature, is meaningless.

Equilibrium (serving) pressure is the regulator setting where the CO₂ in the headspace exactly balances the CO₂ dissolved in the beer. At that pressure the carbonation neither rises nor falls, whether you are carbonating a fresh keg or pouring from a finished one.

Formula

The pressure comes from the standard carbonation-chart regression — the polynomial fit to the ASBC CO₂ solubility table behind most published kegging charts (T in °F, V in volumes):

P = −16.6999 − 0.0101059 × T + 0.00116512 × T² + 0.173354 × T × V + 4.24267 × V − 0.0684226 × V²

The result is gauge pressure — what your regulator shows. Conversions shown with the result use 1 psi = 0.0689 bar = 6.895 kPa.

Example

A keg of lager sits at 3.3 °C (38 °F) and should pour at 2.5 volumes. The formula gives 11.2 psi — the same 11 psi the printed carbonation charts show for that cell, and equal to 0.77 bar (77 kPa). Set the regulator to 11 psi and the beer will carbonate to — and stay at — 2.5 volumes.

Accuracy & limitations

  • The regression reproduces the standard carbonation chart to within about half a psi across the accepted range; printed charts round to whole psi, so small differences from a chart are rounding, not error.
  • The result is an equilibrium pressure. It says nothing about how fast the beer carbonates — that depends on time, headspace and agitation — and nothing about pour quality, which depends on your line resistance.
  • Very cold beer at a low target may need no pressure at all: it already holds more CO₂ than the target. In that case no result is shown — the beer would have to warm up or degas to reach the target.
  • Accepted ranges: beer temperature −2–30 °C (28–86 °F), target 1.0–4.0 volumes. Pressures climb steeply at the warm, highly carbonated corner of that range — check your keg and fittings are rated for the result.

FAQ

Can I carbonate faster by turning the pressure up?

Yes — that is burst carbonation. Set the regulator to around 30 psi for 24–36 hours, then drop it to the serving pressure from this calculator and let the beer settle for a day. The risk is overshooting: it is easy to push past the target and end up with foamy, over-carbonated beer that takes days of bleeding off pressure to fix. The slower set-and-forget method — serving pressure from the start — avoids that, but typically takes one to two weeks to reach full carbonation.

The pressure is right but my pours are all foam. Why?

Because dispensing is a balance problem, not just a carbonation problem. The pressure here is the equilibrium pressure: it keeps the CO₂ dissolved in the beer. To pour cleanly, your beer line must resist that pressure by roughly the same amount — a short or wide line lets the beer rush out and the CO₂ breaks out as foam. Line length, line diameter, and the height from keg to tap all change the resistance; they change what you need from your lines, not the equilibrium number itself. Warm beer foams too, so check the keg is actually at the temperature you entered.

Should I enter room temperature or fridge temperature?

Neither — enter the temperature of the beer in the keg. CO₂ solubility depends on the beer's own temperature, and a keg in a 20 °C room can sit at 4 °C for days. If the beer is still chilling down, it is not at equilibrium yet; use its current temperature and expect the carbonation to settle once it reaches serving temperature. A stick-on thermometer strip on the keg is close enough for this calculation.

What if I bottle instead of kegging?

Then pressure is not yours to set — the yeast makes it. Bottle-conditioned beer carbonates from a measured dose of priming sugar, and the amount depends on the CO₂ already dissolved in the beer and your target level. Use the priming sugar calculator on this site: it works out the grams of dextrose, table sugar, DME or honey for your batch size and target, for exactly the same range of carbonation levels.