How to use this calculator
- Enter the liquid-yeast packs you are starting from and their viability. A fresh pack holds about 100 billion cells; leave viability at 95% for a fresh pack and lower it for an older one.
- Choose the agitation method honestly — stir plate, intermittent shaking, orsimple (left alone). It changes the answer more than any other input.
- Enter the starter volume and DME for step 1. About 100 g of DME per litre gives a 1.036 starter; the calculator derives the gravity from the two numbers and expects 1.020–1.060.
- If one step is not enough, tick second step and enter its volume and DME — the yeast from step 1 is decanted and pitched into the fresh wort.
- Enter the batch volume, original gravity and beer type. The result shows the final cell count, how many cells the starter grew, and whether it covers the pitch your batch needs — or how many billion cells it falls short. If you are not growing a starter, theyeast pitch rate calculator gives pack counts directly.
Formula
Growth follows Kai Troester's (Braukaiser) model, the growth equation behind Brewer's Friend's starter calculator. Yeast growth is bought with extract, and how much each gram of extract produces depends on theinoculation rate — the viable cells pitched into the starter, in billions per gram of extract:
Inoculation rate = starting cells (B) ÷ DME (g)New cells = growth per gram × DME (g) · Final cells = starting cells + new cellsOn a stir plate, growth is 1.4 billion new cells per gram of extract while the inoculation rate is below 1.4 B/g; above that the rate declines linearly and reaches zero at 3.5 B/g, where the starter is saturated and cells are only maintained. Intermittent shaking grows a flat 0.62 B/g and a simple, unstirred starter 0.40 B/g, both stopping at the same saturation point. Starter gravity is derived from the DME at about 100 g per litre ≈ 1.036. The pitch check uses the Brewers Association rates — 0.75 million cells/mL/°P for ales, 1.50 for lagers — the same rates as the pitch rate calculator.
Example
One fresh pack (100 billion viable cells) into a 1-litre starter with 100 g of DME on a stir plate: the inoculation rate is 1.0 B/g, so the starter grows 1.4 × 100 = 140 billion new cells, for240 billion in total. A 20-litre ale at 1.050 needs about 186 billion cells, so the starter covers it with room to spare. The same batch as a lager needs about 372 billion — short. Add a second step (decant, then 2 litres with 200 g of DME) and the 240 billion grow by another 280 billion, to520 billion: comfortably pitched.
Accuracy & limitations
- The growth figures are Kai Troester's experimental results as used by Brewer's Friend. For intermittent shaking, Jamil Zainasheff's tables use a higher 0.75 B/g; this calculator uses Troester's 0.62, the conservative figure from the model itself.
- Accepted ranges: 1–20 packs, viability 1–100%, 0.25–10 litres and a derived gravity of 1.020–1.060 per step, batch 1–1,000 litres at OG 1.000–1.200.
- The model has no ceiling on total cells beyond the saturation inoculation rate; for very large starters (over about 5 litres) Brewer's Friend notes the equation may run high.
- Viability is an estimate — age, storage temperature and handling all move it, and only a microscope count settles it. Dry yeast is not modelled here; it is normally pitched by the pack, without a starter.
FAQ
What gravity should a yeast starter be?
Around 1.030–1.040 — roughly 100 g of DME per litre of water. Young yeast growing in weak wort stays healthy and unstressed; a strong starter (above about 1.060) is high in alcohol and osmotic pressure and produces tired cells, while a very weak one (below about 1.020) does not contain enough extract to build many new cells. This calculator accepts 1.020–1.060, derived from the DME and volume you enter, and the classic 100 g/L lands at 1.036, right in the sweet spot.
Is a stir plate really that much better than shaking?
Yes — it is the single biggest lever in this calculator. In Kai Troester's growth experiments, a continuously stirred starter grew about 1.4 billion new cells per gram of extract, intermittent shaking about 0.62, and a starter left alone about 0.40. Constant stirring keeps the yeast in suspension, drives off CO₂ and keeps pulling in oxygen, so the same 100 g of DME grows roughly three and a half times as many cells on a stir plate as in a still flask. If you brew lagers or strong beers regularly, a stir plate pays for itself in saved yeast packs.
When do I need a second (step-up) starter?
When one step cannot reach the cell count: lagers, high-gravity worts, big batches, or an old pack with low viability. Chill the first starter until the yeast settles, pour off (decant) the spent wort, and pitch the yeast slurry into fresh starter wort. The second step starts from everything the first step grew, so growth compounds. Stepping up is also how brewers revive a single old pack or build a pitch from a small culture — just keep each step's inoculation rate in a sensible range: pitching a huge step-1 crop into a tiny step 2 grows almost nothing, because the cells already crowd the available extract.
How accurate is the final cell count?
Treat it as a planning estimate, not a lab count. The growth model comes from controlled experiments (Kai Troester's work, used by the Brewer's Friend calculator) and reproduces published examples closely, but real growth varies with temperature, strain, nutrient levels and how healthy the pack actually was. The viability you enter is the softest number in the whole calculation — a pack's true viability is only known under a microscope with a haemocytometer. If the result is borderline for a lager or a strong wort, step the starter up or add a pack rather than pitching short.