Spirit Blending Calculator – Pearson's Square

Blend two spirits — or a spirit and water — to an exact target strength. Pearson's square turns the three strengths into the volumes of each part to mix.

The stronger of the two, at 20 °C

Enter 0 for plain water

Between the two strengths

Final volume of the finished blend

How to use this calculator

  1. Enter the strength of the stronger component in %vol (ABV), measured or corrected to 20 °C.
  2. Enter the strength of the weaker component — a lower-strength spirit, wine, or 0 %vol for plain water.
  3. Enter the strength you want the finished blend to have. It must lie between the two strengths above.
  4. Enter the total final volume you want and choose its unit: mL, L, US fl oz or US gal.
  5. Measure out the two volumes shown, combine them, and check the result with an alcoholmeter before bottling.

What the inputs mean

The high-strength spirit is whichever liquid is stronger: a cask-strength whisky, a neutral spirit, the heads-heavy fraction of a run. The low-strength spirit is the weaker partner — a lighter spirit, the previous batch, or plain water at 0 %vol. The target strength is the bottling or blending strength you are aiming for, and the total final volume is how much finished blend you want to end up with, not how much of either component you start from.

Typical jobs: marrying a 60 %vol barrel-proof bourbon with a 30 %vol lighter spirit to bottle at 40 %vol; proofing a homemade liqueur base down with a low-strength infusion instead of water, so the flavour survives; or combining two gin batches of different strengths into one consistent bottling run.

Formula — Pearson's square

Pearson's square is the classic distiller's and dairy farmer's shortcut for mixing two liquids to a middle strength. Write the two strengths on the left, the target in the middle, and subtract diagonally: the difference across each diagonal is the number of parts of the component on the opposite side.

Parts of high = target − lowParts of low = high − target

The target is always closer to the component you use more of, which is why each part count comes from the far side of the square. To turn parts into volumes, each component takes its share of the total:

Volume of each part = total volume × its parts ÷ total parts

No density table is involved: the square follows from alcohol conservation alone, because the ethanol in the blend is exactly the ethanol the two components brought in.

Example

Blend a 60 %vol spirit with a 30 %vol spirit to make1 litre at 40 %vol. Pearson's square gives 40 − 30 =10 parts of the strong spirit and 60 − 40 = 20 parts of the weaker one — a simple ratio of 1 : 2. Out of 30 parts in total, that is 10 ÷ 30 × 1000 =333 mL of the 60 %vol spirit and 20 ÷ 30 × 1000 = 667 mL of the 30 %vol spirit.

Accuracy & limitations

  • The proportions are nominal — they assume volumes add up. Blending two spirits of similar composition comes very close to that, so spirit-on-spirit results are effectively exact.
  • With water as the low component, ethanol–water contraction (up to roughly 3–4 %) makes the real final volume slightly smaller than planned. Blending 96 %vol spirit with water to 700 mL at 40 %vol nominally takes 292 mL of spirit and 408 mL of water; after mixing you will have a little under 700 mL. Measure and top up with water to the mark. For an exact water amount in one step, use the alcohol dilution calculator instead.
  • Strengths enter and leave in %vol at 20 °C. Warm or cold samples read wrong on an alcoholmeter, and the blend inherits the error.
  • Mix thoroughly and let the blend rest before the final check: freshly mixed spirits read slightly off until the mixture settles and returns to 20 °C.
  • Accepted ranges: strengths 0–100 %vol with low < target < high; total volume up to 100,000 L.

FAQ

How is this different from the dilution calculator?

The dilution calculator works with a single spirit and pure water, and uses a density table so the water amount accounts for volume contraction exactly. This calculator blends any two liquids — two spirits, or a spirit and water — using Pearson's square proportions. Its volumes are nominal: exact when the two components are both spirits, and a close starting point when one of them is water.

Why did my blend come out slightly under the target volume?

Ethanol and water contract when mixed: the blend takes up less space than the two liquids did separately, by up to about 3–4 % at common drinking strengths. Pearson's square gives nominal proportions, so measure the final volume after mixing and top up with a little more of the low-strength component to reach the volume you planned.

Can I blend to a strength above the stronger spirit or below the weaker one?

No. A blend always lands between its two components, so the target must be strictly between the two strengths. To go higher you need a stronger component; to go lower, a weaker one — or water, which counts as 0 %vol.

Does temperature matter when blending?

Yes. Strengths in %vol are defined at 20 °C, and an alcoholmeter reads high on a warm sample and low on a cold one. Measure both components at 20 °C, or correct their readings with the alcohol temperature correction calculator first — blending from uncorrected readings compounds both errors.