How to use this calculator
- Enter the finished batch volume (gal or L) — the volume the colour is diluted into.
- For each malt, enter its weight and its colour rating from the maltster's specification. There are four slots; leave the ones you do not need empty.
- If your malts are rated in EBC instead of Lovibond, switch the colour unit once — the setting applies to all four slots, and the same goes for the weight unit (lb or kg).
- The result appears instantly: SRM, EBC, the colour name and a swatch. Use a dot or a comma as the decimal separator; changing a unit converts the values you have already entered.
What the inputs mean
Batch volume is the finished volume after the boil. Colour is a concentration, so the same grain bill comes out paler in a bigger batch — MCU divides by this volume.
Malt weight is how much of that malt goes into the mash. Each slot is one malt. If a recipe uses more than four malts, combine the smallest additions of similar malts into one slot; colour adds up linearly before the Morey curve is applied, so grouping barely changes the result.
Malt colour is the rating printed on the malt specification, in degrees Lovibond (°L) or EBC. Base malts are pale (1.5–2.5 °L), crystal and caramel malts add amber and red tones (10–120 °L), and roasted malts are nearly black (300–600 °L) — a small amount of a dark malt moves the colour far more than the same weight of base malt.
Formula
Morey's equation (Dan Morey, 1998) first sums the grain bill into malt colour units, then applies a power curve fitted to measured beer colours:
MCU = Σ (malt colour in °L × weight in lb) ÷ batch volume in galSRM = 1.4922 × MCU^0.6859EBC = SRM × 1.97The exponent below 1 is the point of the model: doubling the MCU less than doubles the SRM, so dark beers are not overestimated the way a linear MCU-to-SRM conversion overestimates them.
Example
A single-malt pale ale: 10 lb of pale malt at 2 °L in a5-gallon batch. MCU = (2 × 10) ÷ 5 = 4.0, so SRM = 1.4922 × 4^0.6859 ≈3.9 SRM, or about 7.6 EBC — a yellow beer. In metric units the same recipe — 4.54 kg in 18.9 L — gives exactly the same result.
Accuracy & limitations
- This is an estimate from specification values. Malt colour varies by maltster and by lot — a spec sheet quotes a range, and the calculator can only use the number you type.
- The boil darkens wort (Maillard reactions, kettle caramelisation) and oxidation darkens finished beer; neither is modelled, so real beer usually lands at or slightly above the prediction.
- Morey predicts the colour of the wort the grain bill produces. A laboratory SRM measurement on finished beer — the number on a commercial label — can differ, because fermentation, finings and filtration all strip some colour.
- Accepted ranges: batch volume 4–800 L (about 1–211 gal), each malt 0–50 kg (about 0–110 lb), malt colour 1–600 °L. At least one malt with some weight is required. Out-of-range values are rejected, not extrapolated.
FAQ
What is the difference between SRM and EBC?
Both measure the same thing — how much light a beer absorbs — on different scales. SRM (Standard Reference Method) is the American scale, used by the BJCP style guidelines and most US recipes. EBC is the European Brewing Convention scale, used on European malt specs and beer labels. The conversion is EBC ≈ SRM × 1.97, so a pale lager at 3 SRM is about 6 EBC and a stout at 35 SRM is about 69 EBC. This calculator always shows both.
Why does my finished beer look darker than the calculation?
The prediction comes from the maltsters' colour ratings, but the boil darkens wort on top of that: Maillard reactions and a long, vigorous boil can add several SRM, and oxidation darkens beer further as it ages. Use the number as the colour of the wort your grain bill produces, then expect the finished beer to land the same or a shade darker — rarely lighter.
What is Lovibond, and what if my malt is specified in EBC?
Degrees Lovibond (°L) is the traditional unit for malt colour: pale base malts sit around 1.5–2.5 °L, crystal malts run 10–120 °L and roasted malts reach 300–600 °L. Many European maltsters publish the same rating in EBC instead. Because EBC ≈ °L × 1.97 for malt specs, you can either divide an EBC rating by 1.97 or simply switch the colour unit in this calculator to EBC and type the number as printed.
Morey, Mosher or Daniels — which formula should I use?
All three start from the same MCU sum but map it to SRM differently. Mosher's linear model (SRM = MCU) works for pale beers but increasingly overestimates as colour rises; Daniels applies a fixed offset, which fixes mid-range beers but still overshoots dark ones. Morey's power curve (SRM = 1.4922 × MCU^0.6859) was fitted against measured beer colours and tracks them best across the whole range, which is why it is the standard in modern brewing software and the model used here. For very pale beers, all three nearly agree.