Refractometer Correction Calculator

Correct a refractometer reading taken after fermentation starts: recover the true final gravity and an ABV estimate from your original and current Brix, with the Sean Terrill cubic.

0–40 °Bx

0–40 °Bx

How to use this correction

  1. Before pitching, read the wort with your refractometer and note the Brix. That is the original Brix.
  2. At any point during or after fermentation, read the beer the same way. That is the current Brix.
  3. Enter both. The corrected final gravity and estimated ABV update as you type.

What the inputs mean

Original Brix is the refractometer reading of the unfermented wort, taken before the yeast went in. It anchors the calculation: the same current reading means different gravities depending on where the beer started. Current Brix is the reading now — it looks like a sugar value but is really sugar plus the optical contribution of the alcohol produced so far, which is exactly what the formula removes.

Formula

The correction is the cubic published by Sean Terrill, fitted to brewing measurements:

FG = 1.001843 − 0.002318474×OB − 0.000007775×OB² − 0.000000034×OB³ + 0.00574×CB + 0.00003344×CB² + 0.000000086×CB³

where OB is the original Brix and CB the current Brix. The original gravity comes from the original Brix with the standard ASBC polynomial, SG = 1 + B ÷ (258.6 − (B ÷ 258.2) × 227.1), and the ABV estimate uses the standard factor, ABV = (OG − FG) × 131.25.

Example

A wort reads 12.0 °Bx before pitching — an OG of 1.0484. A few days into fermentation the refractometer reads 5.5 °Bx. Read naively, 5.5 °Bx would convert to about 1.0217, suggesting a stuck, sweet beer. Corrected with the cubic, the true final gravity is 1.0054 and the estimated ABV is about 5.6% — a dry, nearly finished beer. That gap is why the correction matters.

Accuracy & limitations

  • This is an empirical fit, not a physical law: Terrill derived the coefficients by regressing refractometer readings against measured gravities across many brews.
  • Both readings must be between 0 and 40 °Bx, and the current reading must be below the original.
  • The readings are used as-is, with no wort correction factor applied; if your refractometer's documentation specifies one, divide both readings by it before entering them.

FAQ

Why is a refractometer reading inaccurate after fermentation starts?

A refractometer cannot tell sugar and alcohol apart: both bend light, so once yeast has produced alcohol the reading is pushed high and no longer reflects the remaining sugar. The original reading, taken before any alcohol existed, is still valid — combining the two is what lets the Terrill cubic separate the alcohol's contribution from the sugar's.

How close is the corrected FG to a hydrometer reading?

For typical beer gravities the corrected value usually lands within about 0.001–0.002 SG of a careful hydrometer reading — close enough for tracking fermentation and estimating ABV. The gap grows at very high gravities and with unusual fermentations, so for a final number you will act on (packaging, labelling, competition entries) a hydrometer or lab measurement still wins.

Can I use this to decide fermentation is finished?

Yes, as a tracking tool: take readings on consecutive days and correct each one with the same original Brix. When the corrected FG stops moving for two to three days, fermentation is done. Because the formula is an empirical estimate, confirm with a hydrometer before packaging if the decision is expensive to get wrong.

Do I still need to correct for temperature?

A refractometer is calibrated around 20 °C (68 °F). Most brewing refractometers have automatic temperature compensation that covers roughly 10–30 °C, in which case no extra correction is needed. Without ATC, let the few drops on the prism settle to near 20 °C before reading — the sample is tiny, so it equilibrates in seconds. Take the original and current readings the same way for consistency.