How to use this calculator
- Measure the wine's pH with a calibrated pH meter. Test strips are not accurate enough for sulfite work.
- Measure the current free SO₂ if you can (aeration–oxidation, a Vinmetrica-style analyser, or a titration kit). For a wine that has never been sulfited, enter 0.
- Enter the volume of wine you are treating.
- Set the molecular SO₂ target: 0.5 mg/L for reds, 0.8 mg/L for whites and rosés, or your own value for sweet wines.
- Dissolve the calculated KMS in a little wine or water and stir it in gently and evenly. If using Campden tablets, crush them first and round to the nearest half tablet. Wait at least 24 hours, then measure free SO₂ again.
What the inputs mean
Molecular SO₂ is the tiny share of free SO₂ present in its antimicrobial form. It is the number winemakers actually manage to: 0.5 mg/L for reds and 0.8 mg/L for whites are the classic targets. The calculator works backwards from that target to the free SO₂ the wine must hold at its pH.
pH controls the conversion. As pH rises, a smaller and smaller share of free SO₂ is molecular, so the wine needs much more free SO₂ in total. Between pH 3.2 and 3.8 the required free SO₂ more than doubles, which is why two wines rarely need the same addition.
Free vs. bound SO₂: added sulfite splits into free SO₂, which protects the wine, and bound SO₂, which is tied up by acetaldehyde, sugars, pigments and other compounds and is mostly inactive. This calculator doses only the free fraction; it does not try to predict how much will bind.
Current free SO₂ is what the wine already holds, and it counts toward the target — the calculator only adds the gap. If the wine is already at or above target, the result is zero and nothing should be added.
Formulas
Free SO₂ needed for the molecular target (pKa 1.81 under wine conditions):
Target free SO₂ = molecular target × (1 + 10^(pH − 1.81))Only the gap is added:
Addition (mg/L) = max(0, target free − current free)Potassium metabisulfite is 57.6 % SO₂ by weight; one Campden tablet holds about 0.44 g of it:
KMS (g) = addition × litres ÷ 1000 ÷ 0.576 · Tablets = KMS (g) ÷ 0.44Example
A white wine of 20 litres at pH 3.5 with a molecular target of0.8 mg/L and no free SO₂ yet needs a free SO₂ of 0.8 × (1 + 101.69) ≈40.0 mg/L. The addition is the full 40.0 mg/L, which is 40 × 20 ÷ 1000 ÷ 0.576 =about 1.39 g of potassium metabisulfite (0.05 oz) — roughly 3.2 Campden tablets.
Accuracy & limitations
- The result is a free-SO₂ addition only. Bound SO₂ is ignored: part of every dose binds within about a day, so re-measure after 24 hours instead of assuming the full addition stayed free — especially in sweet or oxidized wines, which bind far more.
- The formula assumes potassium metabisulfite at 57.6 % SO₂. Sodium metabisulfite is about 67 % SO₂ and adds sodium to the wine, so it cannot be swapped in gram-for-gram.
- Campden tablets are nominally 0.44 g of KMS, but brands vary; for small batches a scale is more accurate than tablet counts.
- There is no temperature term: unlike alcohol or hydrometer readings, the molecular fraction is set by pH, not cellar temperature.
- Keep an eye on total SO₂ over the wine's life — legal limits are roughly 150–200 mg/L total SO₂ (EU dry wines) and 350 mg/L (US). Every addition in this calculator counts toward that total.
- Accepted ranges: 1–1000 L, pH 2.5–4.5, molecular target 0.1–2.0 mg/L, current free SO₂ 0–200 mg/L.
FAQ
Why does pH matter so much for sulfite additions?
Only the molecular fraction of free SO₂ actually protects wine against microbes and oxidation, and pH sets how large that fraction is. At pH 3.0 about 6 % of free SO₂ is molecular; at pH 4.0 it is under 1 %. Every 0.1 rise in pH means roughly 26 % more free SO₂ is needed for the same protection, so a wine at pH 3.8 needs about two and a half times the free SO₂ of one at pH 3.4. That is why a flat 'add 50 mg/L' rule under-protects high-pH wines and over-sulfites low-pH ones — and why a pH meter matters more here than a precise scale.
Which molecular SO₂ target should I use?
The long-standing winemaking guidelines are 0.5 mg/L molecular SO₂ for red wines and 0.8 mg/L for whites and rosés. Reds get away with less because their tannins and phenolics contribute antimicrobial protection of their own, and because higher SO₂ bleaches red colour and binds to anthocyanins. Wines with residual sugar are at greater risk of refermentation and spoilage, so many winemakers aim higher — around 1.0 mg/L or more — for sweet styles. Use the presets as a starting point and adjust for how the wine will be stored and how long it will age.
Can I add too much sulfite?
Yes. Excess SO₂ gives a burnt-match or pungent smell, a harsh taste, and bleached colour, and it is legally capped: total SO₂ limits are roughly 150 mg/L for dry reds and 200 mg/L for dry whites and rosés in the EU, and 350 mg/L in the US. Remember that every addition counts toward the total, not just toward the free fraction — part of each dose binds and stays in the wine. If a wine needs a large correction, add it in two steps a day or two apart, measuring in between, rather than in one large dose.
When should I measure free SO₂ again after adding?
Wait at least 24 hours. Freshly added sulfite keeps reacting with acetaldehyde, sugars and other compounds, and the free fraction falls noticeably over the first day as binding reaches equilibrium. A reading taken an hour after dosing will flatter the wine. Measure again after a day, and always measure once more in the week before bottling, topping up if the free SO₂ has drifted below target.